background image

Conforms to 

ASTM F1169-10a Full 

Size Crib & F1821

Safety Standards

Style #:

Lot:

Date:

___________

___________

___________

C

4 in 1 Crib

Consumer Care:

 www.DeltaChildren.com

Delta Children’s Products

114 West 26th Street

New York, NY 10001 

Tele.212-645-9033

FACTORY

REV

THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.

To register your product for important safety alerts and updates to your product please 

visit 

www.DeltaChildren.com 

and click on

 

Product Registration

When contacting Delta Consumer Care please reference 

the above information.  Before contacting Delta Consumer 

Care please ensure that the information above matches the 

information found on the label on the Crib End bottom rail, 

please reference the information found on the product 

when contacting Delta Consumer Care. 

Read all instructions before assembly and use.  

KEEP INSTRUCTIONS FOR FUTURE USE

.

     ADULT ASSEMBLY REQUIRED

Due to the presence of small parts during assembly,  keep out of 

reach of children until assembly is complete.

AUGUST 30, 2013, 21127, R12

©2013 DELTA ENTERPRISE CORP.

Summary of Contents for 7886

















Reviews: