background image

4

Fig. 4

Fig. 2

Fig. 3

1. Bench Oscillating Spindle Sander

2. Spindle Adapter

3. 1" I.D. Table Insert

4. 1-3/4" O.D. Drum Washer

5. Arbor Screw

6. 3/4" Sanding Drum & 3/4” Abrasive Sleeve

7. 3/16" Allen Wrench

8. 1/2" Socket Wrench

9. Dust Bag

A. Four Legs - 27-1/2" long

B. Two Upper Front and Rear Braces -11-1/2" long

C. Two Upper Side Braces - 21-5/16" long

D. Two Lower Front and Rear Braces -17-1/8" long

E. Two Lower Side Braces - 26-5/8" long

F.

M8 Hex Nuts - (36)

G. 3/8" Flat Washers - (40)

H. M8 x 20mm Carriage Bolts - (32)

I.

M8 x 45mm Hex Head Screws (4)

J.

Plastic Feet (4)

ASSEMBLY INSTRUCTIONS

WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE SANDER TO THE POWER SOURCE
UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU HAVE READ AND UNDERSTOOD

THE ENTIRE OWNERS MANUAL. NOTE:

This manual contains instructions for assembling the accessory

Model 50-780 steel stand. If the stand was not purchased with the machine, place the machine on a firm sup-
porting surface and proceed with instructions for 

“ASSEMBLING SPINDLE ADAPTER”

.

ASSEMBLING OPTIONAL
ACCESSORY STAND

1.

Assemble the 50-780 stand (Fig. 4) using the 32

carriage bolts, flat washers and nuts supplied. The
two 11-1/2" long upper braces (A); 21-5/16" long
upper braces (B); 17-1/8" long lower braces (C); and
26-5/8" long lower braces (D) should be fastened to
the four 27-1/2" long legs (E). 

IMPORTANT: The top

lips of the upper braces (A) should be over the top
lips of upper braces (B)

.

2.

Attach a plastic foot (F) Fig. 4, to the bottom of

each leg (E).

1

2

3

4

5

6

7

8

9

B

D

E

F

G

H

I

J

A

C

A

B

C

D

E

F

F

Summary of Contents for 31-780












Reviews: