background image

 

 

 

Copyright Information 

© 2018 Delta Tau Data Systems, Inc. All rights reserved. 

This  document  is  furnished  for  the  customers  of  Delta  Tau  Data  Systems,  Inc. 
Other  uses  are  unauthorized  without  written  permission  of  Delta  Tau  Data 
Systems, Inc.  Information contained in this manual may be updated from time-to-
time due to product improvements, etc., and may not conform in every respect to 
former issues. 

To report errors or inconsistencies, call or email:  

Delta Tau Data Systems, Inc. Technical Support 

Phone: (818) 717-5656 

Fax: (818) 998-7807 

Email: 

[email protected]

 

Website: 

http://www.deltatau.com 

 

Operating Conditions 

All  Delta  Tau  Data  Systems,  Inc.  motion  controller  products,  accessories,  and 
amplifiers contain static sensitive components that can be damaged by incorrect 
handling.    When  installing  or  handling  Delta  Tau  Data  Systems,  Inc.  products, 
avoid contact with highly insulated materials.  Only qualified personnel should be 
allowed to handle this equipment. 
 
In the case of industrial applications, we expect our products to be protected from 
hazardous or conductive materials and/or environments that could cause harm to 
the  controller  by  damaging  components  or  causing  electrical  shorts.    When  our 
products  are  used  in  an  industrial  environment,  install  them  into  an  industrial 
electrical  cabinet  or  industrial  PC  to  protect  them  from  excessive  or  corrosive 
moisture, abnormal ambient temperatures, and conductive materials.  If Delta Tau 
Data  Systems,  Inc.  products  are  directly  exposed  to  hazardous  or  conductive 
materials and/or environments, we cannot guarantee their operation.  

Summary of Contents for 3-4112 Series






















Reviews: