Delta Electronics DNL Series Supplementary Manual Download Page 7

 

8.2 Output Characteristics

 

 

8.2.1 Line Regulation 

 

Line Regulation Deviation is defined as the change in output voltage caused by varying the 
input voltage over a specified range while the output load and temperature remain constant. 

 

Test 

1)  Turn on the fan.  
2)  Set the output power to the desired operating point. 
3)  Set the switch SW2 to the converter ON. 
4)  Adjust the input voltage across the converter’s input range (refer to specified range) while 

monitoring DVM2. 

5)  Note the m/- deviation of the output voltage over the full range of the input 

operating voltage (please refer to the data sheet for the detailed specification). 

 

8.2.2 Load Regulation 

 

Load Regulation Deviation is defined as the change in output voltage caused by varying the 
output load current over the specified range (no load to full load) while the input voltage and 
temperature remain constant. 

 

Test 

1)  Turn on the fan. 
2)  Set the input voltage to the desired operating level while monitoring DVM2. 
3)  Set the switch SW2 to the converter ON. 
4)  Adjust the output load across the converter’s operating load range. 
5)  Note the m/- deviation of the output voltage over the full range of the operating 

load range (please refer to the data sheet for the detailed specification). 

 

8.2.3 Output Ripple 

 

Output Ripple is defined as the periodic AC component on the DC/DC converter’s output 
voltage. The output ripple is measured in terms of peak to peak and RMS values, both done 
with a specific bandwidth. 

 

Test 

1)  Turn on the fan. 
2)  Set the switch SW2 to the converter ON. 
3)  Adjust the input voltage while monitoring DVM2 and set the output load to the full rated 

load current. 

4)  Adjust channel 2 on the oscilloscope to be AC coupled at 4µS/Div and at 10mV/Div using 

the 20 MHz bandwidth-limit option on the scope.

 

5)  The output ripple of the DC/DC converter is measured at full load operating power

  
 

Summary of Contents for DNL Series





















Reviews: