Delta Controls RTS-20 Series Installation & Application Manual Download Page 1

Document Edition 2.3

 

 

Page 1 of 13 

INSTALLATION & APPLICATION GUIDE 

 

 

Room Temperature Sensor

 

 

RTS-20xxx (Rev 3.0)

Document Edition 2.3

 

Product Description 

 
Delta’s 

Room Temperature Sensors

 are stylized, 

wall mountable devices used to provide remote 
room temperature sensing to Delta’s ORCA 
system.  The RTS-20 comes with a precision 
temperature sensor and uses the durable and 
attractive plastic housing of Delta’s BACstat II™.  
Options for this device include a RJ-11 service 
port and an Occupancy Override Push-button and 
Setpoint Adjustment Thumb Wheel. 

 

Room Temperature Sensors are ideal for providing 
remote temperature sensing, occupancy override 
for room schedule control, and remote network 
access points. 

 

 

 

 

Contents 

 

MODEL NUMBERS ............................................................................................................. 2

 

PACKAGE CONTENTS ...................................................................................................... 2

 

OTHER RELEVANT DOCUMENTS................................................................................. 2

 

PRODUCT SPECIFICATIONS........................................................................................... 3

 

IMPORTANT INFORMATION.......................................................................................... 4

 

JUMPERS .............................................................................................................................. 5

 

WIRING DIAGRAM ............................................................................................................ 6

 

BOARD LAYOUTS............................................................................................................... 7

 

MOUNTING .......................................................................................................................... 9

 

POWER (ONLY RTS-20JXX) ............................................................................................. 9

 

NETWORK & CABLING REQUIREMENTS (ONLY RTS-20JXX) ............................. 9

 

NETWORK TOPOLOGY (ONLY RTS-20JXX)............................................................. 11

 

NETWORK COMMUNICATIONS SETUP (ONLY RTS-20JXX) ............................... 11

 

APPLICATION NOTES..................................................................................................... 12

 

PROGRAMMING (FOR PUSH BUTTON) ..................................................................... 12

 

CAUTIONS AND WARNINGS ......................................................................................... 13

 

Summary of Contents for RTS-20 Series














Reviews: