Delta Controls DLC-G1212 Installation & Application Manual Download Page 13

Delta Controls 

Cautions and Warnings 

 

WARNING

 

The GE Lighting Controller is an Electro-statically sensitive device.  Proper ESD protection 
(ground strap) should be used when installing this product so that damage to the product does 
not occur. 
 

 
 

Compliance Declarations 

 

BACnet Testing Labs

 

The Delta Controller Engine (DCE) used in this product is BTL listed (with at least V3.22 firmware). 

Refer to 

http://www.bacnetassociation.org/bacnet_testing.htm

 for more detailed product listing information. 

 

 

BACnet is a registered trademark of ASHRAE.  ASHRAE does not endorse, approve or test 
products for compliance with ASHRAE standards.  Compliance of listed products to 
requirements of ASHRAE Standard 135 is the responsibility of the BACnet Manufacturers 
Association (BMA).  BTL is a registered trademark of the BMA. 

 
FCC Compliance Information 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to 
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, 
may cause harmful interference to radio communications. Operation of this equipment in a residential area is 
likely to cause harmful interference in which case the user will be required to correct the interference at his 
own expense. 

 
Industry Canada Compliance Statement 

ICES-003   This Class A digital apparatus meets all requirements of the Canadian Interference-Causing 

Equipment Regulations 

 

Cet appareil numérique de la Classe A Respecte toutes les exigences du Règlement sur le matérial 
brouiller du Canada. 

 

Document Edition 1.5

 

 

Page 13 of 15 

Summary of Contents for DLC-G1212
















Reviews: