background image

2

NOTES ON ASSEMBLY:

-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on 

the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape 

specified in the instructions.

-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly 

recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.

NOTES ON CARE AND MAINTENANCE:

Do not

 scratch or chip the finish.

- Inspect the product periodically, contact delta children's products for replacement parts or questions.

Do not

 store the product or any parts in extreme temperatures and conditions such as a hot attic or a 

damp, cold basement. These extremes can cause a loss of structural integrity.

-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or 

felt pad under any items you place on the finish.

-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.  

-

Do not

 use abrasive chemicals.  

-

Do not

 spray cleaners directly onto furniture.

-Lift slightly when moving on carpeting to prevent leg breakage.

-Use of a vaporizer near furniture will cause wood to swell and finish to peel.

NOTES ON USE:

Keep children and others safe by following these simple rules:

Do not

 allow any child to play on furniture

Do not

 allow climbing on any piece of furniture.

Do no

t allow hanging from any piece of furniture.

- Always monitor your child’s activity when in the nursery.

WARNING

:

 CHANGING TABLE

Fall hazard - to prevent death or serious injury, always keep child within arm’s reach.

Read all instructions before use of the changing table.

KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE.

Inspect the changing table periodically.  

Do not

 use the changing table if it is damaged or broken. 

Contact Delta Children’s Products with any questions.

Tighten all loose screws and bolts before each use.

The maximum recommended weight of the child is 30lbs for the changing table.

Use only the pad provided by Delta Children’s Products.

Summary of Contents for 73075














Reviews: