1 - Wall Slide Bar with adjustable
ADA Slide Mechanism
1 - Full Spray Hand Shower with Rub Clean
and Dual Check Valves
1 - 60” UltraFlex
®
Hose or 69”
Double Spiral Hose
1 - Set of Mounting Hardware
Six (6) #10 x 2-1/2” Wood Screws
Parts and Hardware included:
2.
1.
3.
Install
Mount/Slide
Bracket.
Reference
Mount/Slide
Bracket
instruction
installation
(separate
Sheet).
• Slot-headed screwdriver
• Electric drill
• 5/32” drill bit
• Soft cloth
• Wrench or pliers
Tools Needed for Installation:
WARNING
Prior to snapping the
two cover flanges in
place, make certain
the Wall Slide Bar
is installed securely.
Then snap the two
cover flanges into
place, pressing tightly
so the three catches
on each wall flange
lock into position.
4.
For installation with an existing
shower head, remove the shower
head by turning counter-clockwise
with adjustable wrench or pliers.
Be careful not to unscrew the
shower arm - hold the shower arm
secure while unscrewing the shower
head.
Note: If the existing shower
arm has an integral ball connector,
replace it with a standard, 1/2”
threaded shower arm.
Side View
Vertical Mount
Wood
Screw
Wallboard
Slide
Bar
Wood Wall Stud
Wallboard
Top
Wood
Screw
Bottom
Wood Screw
Located Below
Top Wood Screw
In Wall Stud
Slide
Bar
Top View
Horizontal Mount
SLIDE BAR MAY NOT PROVIDE DESIGNED AMOUNT OF SUPPORT UNLESS
THESE INSTALLATION INSTRUCTIONS ARE STRICTLY FOLLOWED.
For proper installation, both ends of Slide Bar MUST be installed into a wall stud.
For solid support, at least two (2) of the three (3) screws on each end of the
Slide Bar MUST go through the wallboard or tile and be tightly secured into the
wall stud. Given standard stud sizes, only two (2) of the three (3) screws may
screw into the wall stud.
Slide Bar may be installed vertically, horizontally or at an angle, so long as
at least two (2) of the three (3) mounting screws on each end of the Slide
Bar are secured into a wall stud. Locate the wall studs behind the wall before
beginning installation (a stud finder can be obtained from a hardware store).
WARNING
THE FOLLOWING STEPS REQUIRE DRILLING INTO THE WALL.
When drilling into the wall, exercise care to avoid any electrical wiring or
plumbing that may be located behind the wall. Damaged electrical wiring can
cause electrical shock and/or fire. Since older homes do not always fall in line
with current housing codes and requirements, know where internal wall wiring
is located so that no wires will interfere with your installation.
PROPER INSTALLATION IS EXTREMELY IMPORTANT. IF IN DOUBT,
INSTALLATION SHOULD BE DONE BY A QUALIFIED PROFESSIONAL.
USING SLIDE BAR:
1. Read, understand and follow the information in the SAFETY WARNINGS
section of this instruction Sheet. Delta Faucet shall have no liability
for any damage or injury caused by improper installation or use of
this Slide Bar.
2. Grasp the Slide Bar when exiting or entering the bathtub or shower.
3. Use EXTREME caution on wet tub or floor surfaces.
4. DO NOT put entire weight on Slide Bar. Slide Bar is rated for persons
weighing up to
300 pounds when properly installed.
5. DO NOT stand, sit or step on Slide Bar. DO NOT use Slide Bar as a step or
platform to reach area above the tub.
Use the bar for assistance ONLY.
CARE AND MAINTENANCE:
1. Use of mild soap and water or a non-abrasive cleaner is recommended
for cleaning.
2. Periodically inspect the Slide Bar for damage or looseness. DO NOT use
if any damage or looseness exists. Contact your authorized dealer for
assistance.
3. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
BEFORE INSTALLING SLIDE BAR:
1. Remove the Slide Bar and parts from the package. If concealed mount
Slide Bar is used, move cover plates away from mounting holes.
2. Determine where you want to install Slide Bar.
3. Place Slide Bar on wall at desired position. If mounting horizontally or vertically,
check that the Slide Bar is level.
4. With a pencil, mark the centers of the mounting hole positions on one end.
These are the points where you will later drill pilot holes for putting in the
screws.
5. Repeat Step 4 for the other end of the Slide Bar.
TO INSTALL INTO WOOD WALL STUDS:
6. Put on safety glasses before starting.
7. Use the 3/8” power drill and 5/32” drill bit to drill all holes into the wall and wood
wall studs at the marked positions. NOTE: If installing Slide Bar over ceramic
tiles, the 1/4” carbide tip drill bit will be needed for drilling through the tile, in
order to prevent damage to the tiles. Drill pilot holes through the tiles by using a
1/4” carbide tip drill bit. Once a hole has been drilled through the ceramic tiles,
use the 5/32” drill bit to drill a pilot hole in the wood wall stud itself.
8. Place Slide Bar on wall, aligning mounting holes with the holes in the wall.
9. Insert the wood screws provided into one end of the Slide Bar. Screw into wall
and wall stud
(HAND TIGHTEN ONLY).
10. Repeat Step 4 for opposite end of the Slide Bar.
11.
Securely
tighten all mounting wood screws with a screwdriver.
12. If concealed mount Slide Bar is used, move cover plates
over mounting holes and firmly press against the wall.
Cover
Plate
Mounting
Holes
Cover Plate
Concealed Mount Slide Bar
Mounting
Holes
Exposed Mount Slide Bar
Wood Wall Stud
Wood Wall
Stud
INSTALLATION INSTRUCTIONS FOR
ADA WALL SLIDE BAR & HAND SHOWER SYSTEM
72638
Models
52001, 52002, 52003 & 52008
Series
1
10/20/11 Rev. A
www.deltafaucet.com
ASME A112.18.1 / CSA B125.1
72638 Rev A.indd 4
11/15/11 4:33 PM
