background image

9

Operation

FAN MODE

Adjust fan speed by pressing the FAN button (

C

) as described for the air-conditioning mode.

Remember that the higher the speed, the more air is filtered. If you select "

MIN

" speed, less air is

filtered but the appliance is also less noisy.

DEHUMIDIFYING MODE

Ideal for reducing the humidity in a room without lowering or raising the temperature (spring or
autumn, damp rooms, rainy spells, etc).
When the dehumidifying mode is selected,  the light (

P

) comes on.

At the same time, the "

MIN

" fan speed light (

M

) comes on. In this mode, other speeds cannot be

selected.

PROGRAMMING THE TIMER

The timer can be used to delay appliance start up or shut down. This avoids wasting electricity by
optimising operating periods.

How to programme delayed start up

Plug the appliance into a mains socket and press the ON/OFF button (

A

), then select the

required operating mode and other settings (temperature, fan speed, etc).

Press the ON/OFF button (

A

) again to place the appliance in standby mode.

Press the timer button (

D

). The timer light "

H

" flashes.

Use the + (

E

) or - (

F

) buttons to set the number of hours delay before the appliance comes on.

The time increases or decreases in steps of one hour.

The indicator light (

H

) flashes until the appliance starts up.

You can set the appliance to come on with a delay of up to 12 hours.
To cancel the timer programme, press the timer button (

D

) again.

Light (

H

) stops flashing.

How to programme delayed shut down

Delayed shut down can be programmed in any operating mode (air conditioning / fan/ dehu-
midifying).

Press the timer button (

D

). The timer light "H" flashes.

Use the + (

E

) or - (

F

) buttons to set the number of hours delay before the appliance goes off.

The time increases or decreases in steps of one hour.
The light (

H

) flashes until the appliance turns off as programmed. 

At the set time, the air conditioner shuts down and remains in standby.
To cancel the timer programme, press the timer button (

D

) again.

Light (

H

) stops flashing.

Summary of Contents for PAC N120














Reviews: