6
7
- Fix the foot with the screw (
F
) supplied (figure 3).
- See Figure 4 for the minimum distances of the device
from the walls. The measurements are indicated both for
models equipped with fan " " and for models without.
Important!
never use the appliance without the feet
attached if it is not mounted on the wall.
Installation on the wall
The kit for wall installation contains:
2 metal brackets for mounting above (
G
)
2 metal brackets for mounting below (
H
)
2 screws 3.5 x 9.5 PH (
I
)
4 screws 4.5 x 25 PH (
J
)
4 plastic wall plugs 6 x 30 (
K
)
Tools required for installation and estimated time for
installation
Screwdriver PH 2x100 (crosshead)
Estimated time for installation: 30 minutes
Before installing the unit, ensure the following:
a. The device must not be placed directly under a
power socket.
b. The plug and power socket must be easy to reach
after installation.
c. No electric cables or other pipework could be
damaged during installation.
d. Keep away from curtains or flammable materials.
For wall mounting, proceed as follows:
Place the appliance on a stable surface. Use a screwdriver to fix
the two brackets
H
with screws
I
as shown in Fig. 6.
1. Before drilling the wall, mark the exact spot, respecting
the minimum distances as shown in Fig. 5. The
measurements are indicated both for models equipped
with fan " " and for models without.
2. Drill following the marks that you have made and
insert the wall plugs
K
. For brick walls use a masonry
bit of 6 mm. For plasterboard or false walls (empty), we
recommend the use of appropriate screws and anchors
(not supplied).
3. Fix the 2 metal brackets
G
to the wall using the screws
J
provided.
4. Hang the appliance on the brackets.
5. Mark the lower fixing points corresponding to the holes
of the brackets
H
. Remove the appliance, drill the lower
holes and insert the wall plugs
K
.
6. Now you can hang the unit on the brackets and secure the
bottom of the appliance with the 2 screws
J
remaining.
USE
Operation and use
Insert the plug into the socket and switch on at the socket if
necessary, turn the thermostat knob (
B
) to position 6 and turn
the appliance on via the power selector (
C
) as follows:
• The warning lamp (
A
) lights up.
• Turn the power selector knob to
Min
to select minimum
power.
• Turn the power selector knob to
Med
to select medium
power.
• Turn the power selector knob to
Max
to select maximum
power.
• To switch off the appliance completely: turn the power
selector to "0" and the thermostat to , then disconnect
at the power socket.
Adjusting the thermostat
When the room has reached the required temperature, turn the
thermostat knob (
B
) slowly anticlockwise until you hear a click
and no further. The warning lamp (
A
) goes out.
The thermostat will automatically maintain the temperature.
In spring or autumn or on mild days, you can save energy by
using minimum power.
Freezing protection
With the knob of the thermostat (
B
) in position and one
of the power levels selected, the appliance will maintain the
room at a temperature of about 5°C preventing freezing with
minimum energy consumption.
Models with fan
The appliance is equipped with a fan that provides even more
rapid and uniform heating.
To start this function, turn the power selector (
C
) to Max .
Models with 24-hour timer
When the appliance is connected to the power supply the timer
is always active so as to stay synchronized with the local time.
To operate the appliance without timer, position the timer
slider (
D
) to
.
To operate the appliance at the times set, position the timer
slider to
(Fig. 1) and proceed as follows:
• Check the time on your clock or watch. If it is 10.00 for
example, turn the numbered programmer disk until the
number 10 coincides with the pointer marked on the
programmer device.
• Set the periods of time during which you want the
appliance to operate by pushing the teeth outwards (see
figure). Each tooth corresponds to a period of 30 min. At
the end of the procedure, the sectors corresponding to the
