background image

26

SETTING  THE  TIMER  VOLUME

You  can  select  from  three  volume  levels.

Touch  the  “

”  and  “

”  keys  simultaneously  for  more  than  2  seconds.

Touch  the  “

MODE

”  key;  you  can  read  on  the  display  the  current  timer  volume

(“

ton1

”,  “

ton2

”  or  “

ton3

”).

Touch  the  “

” key  to  listen  or  change  the  timer  volume.

Timer  volume  activated:  the  last  displayed.

After  about  8  seconds  an  acoustic  signal  (“

beep

”)  will  sound  confirming  the  vol-

ume  setting;  then  the  time  of  day  will  be  displayed.

AUTOMATIC  COOKING

Use  automatic  cooking  to  automatically  turn  the  oven  on,  cook,  and  then  turn  the
oven  off.

1. Check  the  clock  shows  the  correct  time.

2. Select the function and temperature (function and temperature knobs). The oven will

come  on.

3. Decide how long the food will take to cook, allowing time for preheating if necessary.

4. Touch  the  “

MODE

”  key  for  more  than  2  seconds  and  then  touch  again.  “

dur

”  will

show  (duration).  Using  the  “

”  and  “

”  keys,  set  the  cooking  time.

5. Decide  the  time  you  would  like  the  oven  to  turn  off;  touch  the  “

MODE

”  key  for

more  than  2  seconds  and  then  touch  it  two  times  again.  “

End

”  will  show.  Using

the  “

”  and  “

”  keys,  set  the  cooking  time.

Note

:  while  “

dur

”  is  displayed  you  can  change  to  “

End

”  just  by  touching  one  time

the  “

MODE

”  key  (within  8  seconds  from  the  last  selection).

If  there  is  time  to  wait  before  cooking  starts,  the  current  time  of  day  and  “

AUTO

”  will

show  in  the  clock  display.  The  oven  will  switch  off  but  is  now  set  for  automatic  cooking. 

If  you  are  already  at  home  to  turn  the  oven  on  and  only  want  the  oven  to  turn  off
automatically,  start  cooking  as  normal,  then  follow  step  4  or  step  5  to  set  a  time  to
stop  the  oven.

When  automatic  cooking  starts,  “

”  will  be  displayed  and  the  oven  will  turn  on.

To  see  the  remaining  cook  time,  follow  step  4  up  to  display  “

dur

”  (duration).

To  see  the  set  stop  time,  follow  step  5  up  to  display  “

End

”.

To  cancel  automatic  cooking  at  any  time,  touch  the  “

”  and  “

”  keys  simultane-

ously  (for  more  than  2  seconds)  and  turn  the  temperature  and  function  knobs  to
the  off  position.

When the stop time is reached, the oven will turn off, the timer will beep and “

AUTO

will  flash:

Touch  any  key  to  stop  the  beeping.

Touch  the  “

MODE

”  key,  for  more  than  2  seconds,  to  return  the  oven  to  the  manu-

al  mode  (“

”  symbol  steady  illuminated  on  the  display).

Turn  the  temperature  and  function  knobs  to  the  off  position.

Attention:  after  a  power  failure  any  automatic  program  is  deleted.  Turn  off
the  oven  manually.

Summary of Contents for DE 91 MPS









































Reviews: