Dell XPS 8920 Service Manual Download Page 46

Page: 46 / 102

Removing the coin-cell battery

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

CAUTION:

Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is recommended that

you note the BIOS setup program’s settings before removing the coin-cell battery.

Prerequisites

1. Remove the

right-side cover

2. Follow the procedure from step 1 to step 2 in “

Removing the power-supply unit

”.

Procedure

1. Using a plastic scribe, press the battery-release lever away from the coin-cell battery until the coin-cell battery pops up.
2. Lift the coin-cell battery out of its socket.

Figure 22. Removing the coin cell battery

1. plastic scribe

2. coin-cell battery

3. coin-cell battery socket

4. battery-release lever

Removing the coin-cell battery

Summary of Contents for XPS 8920







































































































Search results

Summary of Contents for XPS 8920

Reviews:

Related manuals for XPS 8920

Brands by name

Popular brands

Dell XPS 8920, Service Manual

Search results

Summary of Contents for XPS 8920

Reviews:

Related manuals for XPS 8920

Brands by name

Popular brands