Dell Vostro 3400 Service Manual Download Page 12

Page: 12 / 111

Intel UHD Graphics 620

Table 3. Intel UHD Graphics 620 specifications

Intel UHD Graphics 620

Bus Type

Integrated

Memory Type

DDR4

Graphics Level

i3/i5/i7: G T2 (UHD 620)

Estimated Maximum Power Consumption (TDP)

15 W (included in the CPU power)

Overlay Planes

Yes

Operating Systems Graphics/ Video API Support

DirectX 11 (Windows 7/8.1), DirectX 12 (Windows 10), OpenGL 4.3

Maximum Vertical Refresh Rate

Up to 85 Hz depending on resolution

Multiple Display Support

On System: eDP (internal), HDMI

Via Optional USB Type-C Port: VGA, DisplayPort

External Connectors

HDMI 1.4b

USB Type–C port

Nvidia GeForce MX130 equivalent

Table 4. Nvidia GeForce MX130 specifications

Feature

Specifications

Graphics memory

2 GB GDDR5

Bus type

PCI Express 3.0

Memory Interface

GDDR5

Clock Speeds

1122 - 1242 (Boost) MHz

Maximum Color Depth

N/A

Maximum Vertical Refresh Rate

N/A

Operating Systems Graphics/ Video API Support

Windows 10/ DX 12/ OGL4.5

Supported Resolutions and Max Refresh Rates (Hz)

N/A

Numbers of Display Support

No display output from MX130

Technology and components

Summary of Contents for Vostro 3400
















































































































Search results

Summary of Contents for Vostro 3400

Reviews:

Related manuals for Vostro 3400

Brands by name

Popular brands

Dell Vostro 3400, Service Manual

Search results

Summary of Contents for Vostro 3400

Reviews:

Related manuals for Vostro 3400

Brands by name

Popular brands