manualshive.com logo in svg

Dell USC, User Manual

Share
Download
Dell USC User Manual Download Page 55

USC and USC-LCE Operations

55

Rebooting System

Click 

Finish

 to reboot the system and continue with the operating system 

installation. Upon reboot, the system boots to the operating system 

installation media.

 

CAUTION: 

During the beginning of Microsoft Windows Server

®

 2003 installation, 

the installer will automatically detect and possibly assign the default drive letter 
C to USC and USC-LCE temporary storage device OEMDRV. Creating a new 
Windows-bootable system partition on the hard-disk will assign the partition to a 
drive letter other than C; this is standard Windows installer behavior. To assign 
the new partition to C, see 

Assigning a Windows-Bootable System Partition to Drive 

C

.

Post Reboot Scenarios

Table 4-4 lists the post reboot scenarios, its user actions, and impact.

Table 4-4.  Post Reboot Scenarios and User Actions

Scenario

User Action and Impact

USC or USC-LCE prompts you to 

press a key before booting to the 

operating system installation media

Press any key, else the system boots to the 

hard-disk and not the operating system 

installation media.

Operating system installation is 

interrupted and the system reboots 

before installation is completed.

USC or USC-LCE prompts you to press a 

key to boot from the operating system 

installation media.

Want to cancel operating system 

installation.

Press the 

<F10>

 key.

NOTE: 

Pressing the <F10> key at any point 

during the installation process or while 

rebooting causes any drivers provided by the 

OS Deployment wizard to be removed.

Cannot update USC or USC-LCE by 

running a DUP in the operating system 

environment for the next 18 hours

USC or USC-LCE does not allow this after 

the operating system installation.

Summary of Contents for USC





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands