manualshive.com logo in svg

Dell USC, User Manual

Share
Download
Dell USC User Manual Download Page 52

52

USC and USC-LCE Operations

Selecting Operating System

You can select an operating system based on its availability and user 

preference. Take any one of the following action:

•

Selecting an Operating System Available in the List

•

Selecting Custom Operating System

•

Selecting an Operating System Not Available in the List

Selecting an Operating System Available in the List

To install an operating system that is available in the list:

1

From the list, select the required operating systems, and click 

Next

.

2

If a UEFI capable operating system is selected, USC-LCE displays two 

installation modes — 

UEFI

 or 

BIOS

. Select one of options and click 

Next

.

3

Insert the standard operating system installation media when prompted, 

and click 

Next

. USC or USC-LCE validates the media.

 

NOTE: 

USC or USC-LCE renders the drivers through the 

OEMDRV

 directory to 

the operating system.

4

If the standard operating system installation media is validated, continue 

with the installation. Else, insert the correct media and click 

Next

.

Summary of Contents for USC





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands