manualshive.com logo in svg

Dell USC, User Manual

Share
Download
Dell USC User Manual Download Page 51

USC and USC-LCE Operations

51

Using Optional RAID Configuration

If the system has a RAID controller, you can configure a virtual disk as the 

boot device.

Configuring RAID Using Operating System Deployment Wizard

Important

• For USC, the 

Raid Configuration

 wizard is available only through the 

OS Deployment

 wizard.

• For USC-LCE, you can configure RAID through the RAID configuration 

page from the 

Hardware Configuration

 Tab

Configuration Wizards



RAID Configuration

.

 

NOTE: 

ESX 3.5 and Citrix operating systems do not support series 7 

controllers.

To configure RAID using OS Deployment wizard:

1

In the left pane of the 

Home

 page, click 

OS Deployment

.

2

Select

 Configure RAID Now

. This option launches the 

RAID 

Configuration

 wizard that displays all the storage controllers available for 

configuration, including the series 6 and 7 controllers. 

3

Select a storage controller. 
The RAID Configuration options are displayed. 

4

Complete RAID settings and click 

Finish.

The RAID configuration is applied on the disks, and USC or USC-LCE 

returns to the 

OS Deployment

 wizard. 

Bypass RAID configuration:

Select 

Go Directly to OS Deployment

 and click 

Next

. This option launches 

the 

OS Deployment

 wizard and the operating system is installed on the 

default boot device identified in the BIOS utility.

See Also:

•

Selecting Operating System

•

Installing Operating System

Summary of Contents for USC





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands