Dell Studio 1569 Service Manual Download Page 27 | Manualshive

Page: 27 / 47

background image

Replacing the Keyboard

1.

Follow the procedures in

Before You Begin

2.

Place the keyboard upside down on the palm rest and connect the keyboard cables.

a.

Slide the keyboard cable into the system board connector and press the connector tabs into the connector to secure the cable.

b.

If you have a backlit keyboard, slide the keyboard backlight cable into the system board connector and press down on the connector latch to

secure the cable.

3.

Align the tabs on the keyboard with the slots on the palm rest and lower the keyboard into place.

4.

Replace the screw that secures the keyboard to the computer base.

5.

Replace the power button panel (see

Replacing the Power Button Panel

6.

Replace the battery (see

Replacing the Battery

Back to Contents Page

7

keyboard backlight cable

8

palm rest

9

screw

CAUTION:

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may

result in damage to the computer.

«
...
25
26
27
28
29
...
»

Summary of Contents for Studio 1569
















































Reviews:

No comments

Related manuals for Studio 1569

Personal Computer

Brand: IBM Pages: 318

Brand: EAI Pages: 132

POWERMATE ES 5250 - S

Brand: NEC Pages: 18

POWERMATE VT 300 RELEASE NOTES

Brand: NEC Pages: 16

POWERMATE CT 815 - RELEASE NOTES

Brand: NEC Pages: 155

Brand: NEC Pages: 6

POWERMATE ES Series

Brand: NEC Pages: 132

POWERMATE ES Series

Brand: NEC Pages: 8

Brand: NEC Pages: 167

Brand: NEC Pages: 1

Brand: IBM Pages: 164

6219 - IntelliStation M - Pro

Brand: IBM Pages: 154

Brand: IBM Pages: 72

Brand: Roland Pages: 1

Brand: Aaeon Pages: 64

FlowControl FC-S01

Brand: Go!Paint Pages: 20

Brand: Wincomm Pages: 58

Brand: Vivo Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands