Dell S6100 Installation Manual Download Page 49

Page: 49 / 54

Specifications

This topic lists the S6100–ON specifications.

CAUTION:

Operate the product at an ambient temperature not higher than 113°F (45°C).

CAUTION:

Lithium Battery Caution: There is a danger of explosion if the battery is incorrectly replaced. Replace only with same

or equivalent type of battery. Dispose of the batteries according to the manufacturer's instructions.

Topics:

•

Chassis physical design

•

IEEE standards

•

Agency compliance

•

USA Federal Communications Commission (FCC) statement

•

European Union EMC Directive Conformance statement

•

Japan: VCCI Compliance for Class A Equipment

•

Korean Certification of Compliance

•

Safety Standards and Compliance Agency Certifications

•

Electromagnetic Compatibility (EMC)

•

Product recycling and disposal

Chassis physical design

Table 10. Chassis physical design

Parameter

Specifications

Height

3.50 inches (88.9 mm)

Width

17.1 inches (434.3 mm)

Depth

18 inches (457.2 mm)

Chassis Weight with Factory-Installed Components

44 lbs (20 kg)—with two PSUs and four I/O modules

Rack Clearance Required

Front: 5 inches (12.7 cm)

Rear: 5 inches (12.7 cm)

Table 11. Environmental Parameters

Parameter

Specifications

Operating Temperature

32° to 113°F (0° to 45°C)

Operating Humidity

5 to 95 percent (RH), non-condensing

Storage Temperature

–40° to 158°F (–40° to 70°C)

Specifications

Summary of Contents for S6100























































Search results

Summary of Contents for S6100

Reviews:

Related manuals for S6100

Brands by name

Popular brands

Dell S6100, Installation Manual

Search results

Summary of Contents for S6100

Reviews:

Related manuals for S6100

Brands by name

Popular brands