manualshive.com logo in svg

Dell S6100, Configuration Manual

The Dell S6100 Configuration Manual is a comprehensive guide that enables users to maximize the functionality of their Dell S6100 device. This manual can be easily downloaded for free from our website, allowing users to access valuable information and optimize their product experience.

Share
Download
background image

•

For a 50-Gigabit Ethernet interface, enter the keyword 

fiftyGigE

 then the stack/

slot/port/subport information.

•

For a 100-Gigabit Ethernet interface, enter the keyword 

hundredGigE

 then the 

stack/slot/port information.

•

For a Loopback interface, enter the keyword 

loopback

 then a number from 0 to 

16383.

•

For a port channel interface, enter the keywords 

port-channel

 then a number.

•

For a VLAN interface, enter the keyword 

vlan

 then a number from 1 to 4094.

Defaults

Not configured.

Command Modes

CONFIGURATION

Command History

This guide is platform-specific. For command information about other platforms, see the relevant 

Dell Networking 

OS Command Line Reference Guide

.

Version

Description

9.10(0.0)

Introduced on the S6100–ON.

9.8(1.0)

Introduced on the Z9100–ON.

9.8(0.0P5)

Introduced on the S4048-ON.

9.8(0.0P2)

Introduced on the S3048-ON.

9.7(0.0)

Introduced on the S6000-ON.

9.5(0.1)

Introduced on the Z9500.

9.0.2.0

Introduced on the S6000.

8.3.19.0

Introduced on the S4820T.

8.3.11.1

Introduced on the Z9000.

8.3.7.0

Introduced on the S4810.

8.5.1.0

Added support for 4-port 40G line cards on the E-Series.

6.2.1.1

Introduced

ip msdp peer

Configure an MSDP peer.

Syntax

ip msdp peer 

peer address

 [connect-source] [description] [sa-limit 

number

]

To remove the MSDP peer, use the 

no ip msdp peer 

peer address

 [connect-source interface] 

[description 

name

] [sa-limit 

number

]

 command.

Parameters

peer address

Enter the peer address in a dotted decimal format (A.B.C.D.).

connect-source 

interface

Enter the keywords 

connect-source

 then one of the interfaces and slot/port or 

number information:

Multicast Source Discovery Protocol (MSDP)

991

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S6100

D-Link xStack User Manual preview
xStack
Brand: D-Link Pages: 357
KE2 20543 Quick Start Manual preview
20543
Brand: KE2 Pages: 4
IBM E12 Quick Installation Manual preview
E12
Brand: IBM Pages: 2
Xantech D5SH Installation Instructions Manual preview
D5SH
Brand: Xantech Pages: 20
ifs POC2502 Series User Manual preview
POC2502 Series
Brand: ifs Pages: 352
D-Link DES-3224 - Switch User Manual preview
DES-3224 - Switch
Brand: D-Link Pages: 75
socomec 95333400 Instruction Manual preview
95333400
Brand: socomec Pages: 43
Vivotek AW-FGT-100C-120 Quick Installation Manual preview
AW-FGT-100C-120
Brand: Vivotek Pages: 2
N-Tron 716M12 User Manual & Installation Manual preview
716M12
Brand: N-Tron Pages: 169
Endress+Hauser Liquipoint FTW33 Operating Instructions Manual preview
Liquipoint FTW33
Brand: Endress+Hauser Pages: 48
hager EHN010 Installation And Instruction Manual preview
EHN010
Brand: hager Pages: 6
HighSecLabs K304 Quick Start Manual preview
K304
Brand: HighSecLabs Pages: 2
TLS Electronics 875300 User Manual preview
875300
Brand: TLS Electronics Pages: 12
DSPPA MAG-808 User Manual preview
MAG-808
Brand: DSPPA Pages: 31
Versa Technology VX-IGP-1204F User Manual preview
VX-IGP-1204F
Brand: Versa Technology Pages: 96
Inline 62652I Quick Installation Manual preview
62652I
Brand: Inline Pages: 4
LevelOne GSW-1601TX User Manual preview
GSW-1601TX
Brand: LevelOne Pages: 40
EGig eG1G8T User Manual preview
eG1G8T
Brand: EGig Pages: 10

Brands by name

Popular brands

Load more brands