Dell S6100 Configuration Manual Download Page 941

Page: 941 / 1743

Dell(conf-if-vl-222)#do show vlan name test

Codes: * - Default VLAN, G - GVRP VLANs

Q: U - Untagged, T - Tagged

x - Dot1x untagged, X - Dot1x tagged

G - GVRP tagged, M - Vlan-stack

NUM Status Description Q Ports

222 Inactive U Te 1/1/2/1

Dell(conf-if-vl-222)#

Example (OpenFlow
instance)

NUM Status Description Q Ports

* 1 Inactive

3 Inactive

O 6 Inactive

O 8 Inactive

O 12 Inactive O Te 1/1/1/1

Related Commands

•

vlan-stack compatible

— enable the Stackable VLAN feature on the selected VLAN.

•

interface vlan

— configure a VLAN.

tagged

Add a Layer 2 interface to a VLAN as a tagged interface.

Syntax

tagged

interface

To remove a tagged interface from a VLAN, use the

no tagged

interface

command.

Parameters

interface

Enter the following keywords and the interface information:

•

For a port channel interface, enter the keywords

port-channel

then a number.

•

For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then

the stack/slot/port/subport information.

•

For a 25-Gigabit Ethernet interface, enter the keyword

twentyFiveGigE

then the

stack/slot/port/subport information.

•

For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the stack/

slot/port[/subport] information.

•

For a 50-Gigabit Ethernet interface, enter the keyword

fiftyGigE

then the stack/

slot/port/subport information.

•

For a 100-Gigabit Ethernet interface, enter the keyword

hundredGigE

then the

stack/slot/port information.

Defaults

All interfaces in Layer 2 mode are untagged.

Command Modes

INTERFACE VLAN

Command History

This guide is platform-specific. For command information about other platforms, see the relevant

Dell Networking

OS Command Line Reference Guide

Layer 2

941

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for S6100

Reviews:

Related manuals for S6100

Brands by name

Popular brands

Dell S6100, Configuration Manual

Search results

Summary of Contents for S6100

Reviews:

Related manuals for S6100

Brands by name

Popular brands