manualshive.com logo in svg

Dell S6100, Configuration Manual

The Dell S6100 Configuration Manual is a comprehensive guide that enables users to maximize the functionality of their Dell S6100 device. This manual can be easily downloaded for free from our website, allowing users to access valuable information and optimize their product experience.

Share
Download
background image

Related Commands

•

show interfaces configured

 – display any interface with a non-default configuration.

•

show ip interface

 – display Layer 3 information about the interfaces.

•

show range

 – display all interfaces configured using the interface range command.

show interfaces configured

Display any interface with a non-default configuration.

Syntax

show interfaces configured

Command Modes

•

EXEC

•

EXEC Privilege

Command History

This guide is platform-specific. For command information about other platforms, see the relevant 

Dell Networking 

OS Command Line Reference Guide

.

Version

Description

9.10(0.1)

Introduced on the S6010-ON and S4048T-ON.

9.10(0.0)

Introduced on the S6100–ON.

9.8(2.0)

Introduced on the S3100 series.

9.8(1.0)

Introduced on the Z9100–ON.

9.8(0.0P5)

Introduced on the S4048-ON.

9.8(0.0P2)

Introduced on the S3048-ON.

9.7(0.0)

Introduced on the S6000-ON.

9.2(1.0)

Introduced on the Z9500.

9.0.2.0

Introduced on the S6000.

8.3.19.0

Introduced on the S4820T.

8.3.11.1

Introduced on the Z9000.

8.3.7.0

Introduced on the S4810.

8.1.1.0

Introduced on the E-Series.

7.6.1.0

Introduced on the S-Series.

7.5.1.0

Introduced on the C-Series.

6.4.1.0

Changed the organization of the display output.

Example

Dell# show interfaces configured

TenGigabitEthernet 1/1/1/1 is up, line protocol is up

Hardware is Force10Eth, address is 00:01:e8:05:f7:fc

  Current address is 00:01:e8:05:f7:fc

Interface index is 474791997

Internet address is 1.1.1.1/24

MTU 1554 bytes, IP MTU 1500 bytes

LineSpeed 1000 Mbit, Mode full duplex, Master

ARP type: ARPA, ARP Timeout 04:00:00

Last clearing of "show interfaces" counters 00:12:42

Queueing strategy: fifo

706

Interfaces

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S6100

IBM RackSwitch G8264 Product Manual preview
RackSwitch G8264
Brand: IBM Pages: 20
IBM Flex System FC3171 Installation And User Manual preview
Flex System FC3171
Brand: IBM Pages: 64
IBM 8237 Installation And User Manual preview
8237
Brand: IBM Pages: 166
Edge-Core AS7726-32X Quick Start Manual preview
AS7726-32X
Brand: Edge-Core Pages: 9
Hamlet XHUB330LAN User Manual preview
XHUB330LAN
Brand: Hamlet Pages: 4
Allen-Bradley Guard Master 440N-Z2NRS1A Installation Instructions preview
Guard Master 440N-Z2NRS1A
Brand: Allen-Bradley Pages: 4
Orei UHD-401MV User Manual preview
UHD-401MV
Brand: Orei Pages: 27
Maiwe MIEN2205 User Manual preview
MIEN2205
Brand: Maiwe Pages: 5
Zonet KVM3324 Installation Manual preview
KVM3324
Brand: Zonet Pages: 7
Planet WGSW-5240 Specifications preview
WGSW-5240
Brand: Planet Pages: 2
Barksdale 9671 Series Operating Instructions Manual preview
9671 Series
Brand: Barksdale Pages: 6
Alps Electric SKRN Series Specifications preview
SKRN Series
Brand: Alps Electric Pages: 4
Linksys SRW2024P User Manual preview
SRW2024P
Brand: Linksys Pages: 110
IMC Networks Giga-AcessEtherLinx-II Operation Manual preview
Giga-AcessEtherLinx-II
Brand: IMC Networks Pages: 40
rtd IDAN-LAN25255HR User Manual preview
IDAN-LAN25255HR
Brand: rtd Pages: 24
Leonton EG5-0702-SFP Series User Manual preview
EG5-0702-SFP Series
Brand: Leonton Pages: 21
Rosewill RGS-1016 User Manual preview
RGS-1016
Brand: Rosewill Pages: 9
Unipoe P6-S20FL User Manual preview
P6-S20FL
Brand: Unipoe Pages: 6

Brands by name

Popular brands

Load more brands