Dell S3048-ON Configuration Manual Download Page 361 | Manualshive

Page: 361 / 1036

background image

•

Configuring a Broadcast Address

•

Configurations Using UDP Helper

•

UDP Helper with Broadcast-All Addresses

•

UDP Helper with Subnet Broadcast Addresses

•

UDP Helper with Configured Broadcast Addresses

•

UDP Helper with No Configured Broadcast Addresses

•

Troubleshooting UDP Helper

IP Addresses

Dell Networking OS supports IP version 4 (as described in RFC 791), classful routing, and variable length subnet masks (VLSM).

With VLSM, you can configure one network with different masks. Supernetting, which increases the number of subnets, is also supported.
To subnet, you add a mask to the IP address to separate the network and host portions of the IP address.
At its most basic level, an IP address is 32-bits composed of network and host portions and represented in dotted decimal format. For
example, 00001010110101100101011110000011 is represented as 10.214.87.131.

For more information about IP addressing, refer to RFC 791, Internet Protocol.

Implementation Information

You can configure any IP address as a static route except IP addresses already assigned to interfaces.

NOTE:

Dell Networking OS supports 31-bit subnet masks (/31, or 255.255.255.254) as defined by RFC 3021. This feature allows

you to save two more IP addresses on point-to-point links than 30-bit masks. Dell Networking OS supports RFC 3021 with ARP.

NOTE:

Even though Dell Networking OS listens to all ports, you can only use the ports starting from 35001 for IPv4 traffic. Ports

starting from 0 to 35000 are reserved for internal use and you cannot use them for IPv4 traffic.

Configuration Tasks for IP Addresses

The following describes the tasks associated with IP address configuration.

Configuration tasks for IP addresses includes:

•

Assigning IP Addresses to an Interface

(mandatory)

•

Configuring Static Routes

(optional)

•

Configure Static Routes for the Management Interface

(optional)

For a complete listing of all commands related to IP addressing, refer to the

Dell Networking OS Command Line Interface Reference Guide

.

Assigning IP Addresses to an Interface

Assign primary and secondary IP addresses to physical or logical (for example, [virtual local area network [VLAN] or port channel)
interfaces to enable IP communication between the system and hosts connected to that interface.
You can assign one primary address and up to 255 secondary IP addresses to each interface.

1

Enter the keyword

interface

then the type of interface and slot/port information.

CONFIGURATION mode

interface

slot/port

•

For a 1-GigabitEthernet interface, enter the keyword

GigabitEthernet

then the slot/port information.

•

For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

IPv4 Routing

361

«
...
359
360
361
362
363
...
»

Summary of Contents for S3048-ON













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S3048-ON

SmartCell 6A000

Brand: Cabletron Systems Pages: 114

Brand: Cabletron Systems Pages: 62

CyberSWITCH CSX150

Brand: Cabletron Systems Pages: 49

Cabletron CyberSWITCH CSX5500

Brand: Cabletron Systems Pages: 729

Brand: KELCO Pages: 2

Brand: H3C Pages: 13

Brand: H3C Pages: 207

Brand: H3C Pages: 62

DES-3224 - Switch

Brand: D-Link Pages: 75

Aeotec Micro Smart Energy Switch G2

Brand: Aeon Labs Pages: 11

Brand: Witura Pages: 21

Brand: Broadcast Tools Pages: 28

Brand: Teseq Pages: 60

Brand: Ribimex Pages: 15

TEG-S50TXE SHEETS

Brand: TRENDnet Pages: 20

Brand: IPGARD Pages: 2

START-LINE AGC-3500

Brand: Trust Pages: 16

Centerpoint 2x16

Brand: Epicenter Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands