Dell PowerVault 220S Service Manual Download Page 11 | Manualshive

Page: 11 / 32

background image

System Overview : Dell PowerVault 220S and 221S Systems Service Manual

file:///C|/Users/rishi_sood/Desktop/220s/en/sm/intro.htm[3/7/2013 12:09:13 PM]

Drives

SCSI hard drives

support for up to fourteen 1-inch-by-3.5-inch LVD Ultra 160 and Ultra 320 SCSI hot-plug hard drives, at speeds of 10K

or 15K rpm and capacities of 18 GB, 36 GB, 73 GB, 146 GB, or 300 GB

Bus

Configuration

support for any of the following:

one 14-device SCSI bus (joined-bus mode)

one clustered 13-device SCSI bus (cluster mode)

two independent 7-device SCSI buses (split-bus mode)

Back-Panel Connectors

SCSI connector

68-pin shielded P-type SCSI for connection to host

Backplane Board Connectors

SCSI connector

68-pin shielded P-type SCSI for connection to host

Hard drives

fourteen 80-pin SCA-2 connectors

Power supply/cooling module

2 high-current connectors

Enclosure management modules (EMM)

210-pin connector

Split-bus module

180-pin connector

Enclosure Modules

EMM

2 warm-pluggable modules with 68-pin shielded P-type SCSI connectors

Split-bus module

1 warm-pluggable module with an external slide switch to change between split-bus, joined-bus, and cluster modes

SCSI terminator card

1 warm-pluggable module to the terminate SCSI bus in nonredundant EMM configurations

LED Indicators

Front panel

5 LED status indicators for power, fault, split bus, cluster mode, and over-temperature

Hard-drive carrier

1 single-color activity LED and 1 two-color LED status indicator per drive

EMM

3 LED status indicators for power, fault, and active status

Split-bus module

1 LED indicator for power

«
...
9
10
11
12
13
...
»

Summary of Contents for PowerVault 220S

































Reviews:

No comments

Related manuals for PowerVault 220S

Brand: IBM Pages: 2

Brand: Qsan Pages: 28

Brand: PARYA Pages: 6

Brand: Seagate Pages: 40

Ultrastar Serv24 S2122-N24-4

Brand: HGST Pages: 36

Brand: Compaq Pages: 157

Barracuda 180 Family

Brand: Seagate Pages: 2

Brand: QNAP Pages: 68

Brand: Synology Pages: 28

Brand: Clarke Pages: 8

Brand: Fantec Pages: 23

Brand: Dedicated Micros Pages: 12

Brand: Panasonic Pages: 2

Brand: Silvercrest Pages: 18

Installation andMoBox 18160

Brand: Silvercrest Pages: 24

DataBox VI 1000

Brand: Silvercrest Pages: 44

Brand: Silvercrest Pages: 58

Brand: US Polymers Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands