Dell POWEREDGE CLUSTER SE100 Platform Manual Download Page 5

Page: 5 / 18

support.dell.com

Dell PowerEdge Cluster SE100, SE200, and SL200 Platform Guide

Dell™ PowerEdge™ Cluster SE100,

SE200, and SL200 Platform Guide

This guide provides the latest information on using Microsoft

Windows NT

Server

4.0, Enterprise Edition operating system and Windows

2000 Advanced Server oper-

ating system for the following Dell PowerEdge Cluster products and components:

•

Dell PowerEdge Cluster SE100

—

Servers: PowerEdge 2300, 4300, 4350, 6300, and 6350

—

Storage: PowerVault™ 200S, 201S, 210S, and 211S

—

Cluster interconnect: Fast Ethernet

•

Dell PowerEdge Cluster SE200

—

Servers: PowerEdge 2300, 2400, 2450, 4300, 4350, 4400, 6300, 6350,
6400, 6450 and 8450

—

Storage: PowerVault 200S, 201S, 210S, and 211S

—

Cluster interconnect: Fast Ethernet

•

Dell PowerEdge Cluster SL200

—

Servers: PowerEdge 2300, 2400, 2450, 4300, 4350, 4400, 6300,6350, 6400,
6450 and 8450

—

Storage: PowerVault 200S, 201S, 210S, and 211S

—

Cluster interconnect: Giganet cLAN

See the section related to your cluster product for more information on supported
configurations.

NOTE: Configurations not listed in this document are not certified and are not sup-
ported by Dell or Microsoft.

Summary of Contents for POWEREDGE CLUSTER SE100



















Search results

Summary of Contents for POWEREDGE CLUSTER SE100

Reviews:

Related manuals for POWEREDGE CLUSTER SE100

Brands by name

Popular brands

Dell POWEREDGE CLUSTER SE100, Platform Manual

Search results

Summary of Contents for POWEREDGE CLUSTER SE100

Reviews:

Related manuals for POWEREDGE CLUSTER SE100

Brands by name

Popular brands