background image

14

Getting Started With Your System

PowerConnect MPS 1U Shelf

PowerConnect RPS720, MPS600, and MPS1000

1000 W AC-DC power supply

NOTE: 

The power supply has an universal input (100 VAC to 240 VAC). This regulated 

output supplies power to other power supply backup source. The power supply 
incorporates over current protection and OVP.

Input Voltage

Universal input– 100 to 240 VAC

Input Frequency Range

47 to 63 Hz, single phase AC

Max. Input AC Current

12.0 A (maximum) 

Output Voltage and Current

No of Output

1

Nominal Output Voltage Set Point

48 V DC

Set Point Tolerance 

+/- 1%

Total Error Band

+/- 2%

Minimum Current 

1.0 A

Maximum Current 

18.52 A

Physical

Height 

44 mm (1.73 in)

(maximum)

Width 

440 mm (17.32 in)

(maximum)

Depth 

402 mm (15.83 in)

(maximum)

Environmental Considerations

NOTE: 

For additional information about environmental measurements for specific 

system configurations, see 

www.dell.com/environmental_datasheets

.

Temperature

Operating

0° to 45°C (32° to 113°F)

Relative humidity

Operating

0% to 95% (noncondensing) 

Altitude

Operating

0 to 3,048 m (0 to 10,000 ft)

Summary of Contents for PowerConnect MPS 1U Shelf















Reviews: