background image

  4. Disassembly and Assembly Procedures

Use a Philips-head screwdriver to tighten four 

screws for locking mechanisms, then 

.

stick one 

piece of label on the specific positions as the 

picture below shown

(No.1~4 screw size=M4x10; Torque=12 0.5kgfxcm)

±

Move the assembled rear cover close to the 

panel unit, then connect the USB FFC cable to 

the connector of interface board. Put down the 

rear cover and push the rear cover on the 

positions marked as the picture below shown for 

mechanisms engagement.

S17

S16

Put down a rear cover on a protect cushion. Stick 

a piece of aluminum foil on one side of the USB 

hub, then locate the USB unit into the hook of the 

rear cover, then use a Philips-head screwdriver to 

tighten one screw for locking the USB board with the 

USB hub with the middle bezel.

(No.1 screw size=M3x6, Torque=4

±

0.5

kgfxcm)

S15

2

3

4

1

L

c

rovide power supply 

and a video signal to the monitor

ift up the monitor, 

heck the DELL logo if it is firmly 

attached to the front bezel. P

, then turn on the 

monitor for functionality check.

S19

Stick one piece of label on the specific positions as 

the picture below shown. Fit the two tabs on the 

upper part of the stand into the grooves on the back 

of the monitor, and then press the stand so that the 

monitor mounting area snaps onto the stand.

S18

1

Summary of Contents for P2217
















Reviews: