manualshive.com logo in svg

Dell OptiPlex 7090 Tower, Service Manual, Page: 79 / 104

Share
Download
Dell OptiPlex 7090 Tower Service Manual Download Page 79

4. Remove the eight (#6-32) screws that secure the system board to the chassis.
5. Remove the (M2x4) screw that secures the system board to the chassis.
6. Lift the system board at an angle and remove the system board off the chassis.

Installing the system board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the connectors on your system board.

1. CPU power connector
2. Processor fan connector
3. Memory module connector
4. Power button connector
5. Remote power switch connector
6. SD card reader connector
7. SATA0 connector (blue)
8. M.2 PCIe SSD connector
9. Internal USB connector
10. Two SATA1/2 connector (black)
11. SATA3 connector (white)
12. SATA power cable connector
13. Coin-cell battery
14. M.2 WLAN connector
15. System power connector
16. Internal speaker connector
17. Thunderbolt header

Removing and installing components

79

Summary of Contents for OptiPlex 7090 Tower









































































































Reviews:

No comments