manualshive.com logo in svg

Dell OptiPlex 5480 All-in-One, Service Manual

Share
Download
Dell OptiPlex 5480 All-in-One Service Manual Download Page 39

Steps

With the positive-side facing up, insert the coin-cell battery into the battery holder on the system board and gently press the battery until
it snaps into place.

Next steps

1. Install the 

system-board shield

.

2. Install the 

back cover

3. Install the 

cable cover

 (optional).

4. Install the 

stand

.

5. Follow the procedure in 

After working inside your computer

.

Wireless card

Removing the wireless card

Prerequisites

1. Follow the procedure in 

Before working inside your computer

.

2. Remove the 

stand

.

3. Remove the 

cable cover

 (optional).

4. Remove the 

back cover

.

5. Remove the 

system-board shield

.

About this task

The following image indicates the location of the wireless card and provides a visual representation of the removal procedure.

Removing and installing components

39

Summary of Contents for OptiPlex 5480 All-in-One







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands