manualshive.com logo in svg

Dell OptiPlex 100-Mbps, Service Manual

Share
Download
Dell OptiPlex 100-Mbps Service Manual Download Page 74

A-4

Dell OptiPlex GX

pro

 Systems Service Manual

Reserved Memory

Designates a region of system board memory 
that can be supplied by an expansion card.

This feature should not be enabled unless an 
expansion card that requires special addressing 
is installed.

Fast Video BIOS

Enables shadowing and caching the BIOS for a 
video card installed in an expansion slot.

NOTE:  Some video cards are not designed to 
be shadowed or cached.  If video problems 
occur, try setting Fast Video BIOS to Off.

CPU Speed

Indicates processor speed at which system 
boots—the processor’s rated speed or a slower 
compatibility speed.

Num Lock

Determines whether keyboard’s Num Lock 
mode is activated.

Keyboard Errors

Enables or disables reporting of keyboard 
errors during POST.

System Password

Displays current status of system’s password 
security feature.  Also used to assign and verify 
a new password.

Password Status

Provides an extra measure of system security 
by letting you set the system password to 
Locked or Unlocked.

Boot Sequence

Determines whether system boots from dis-
kette (if present) or hard-disk drive.

Setup Password

Restricts access to System Setup program.

Table A-1.  System Setup Categories (continued)

Category

Function

Summary of Contents for OptiPlex 100-Mbps

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands