Dell Networking S6000 System Reference Manual Download

Page: 931 / 1510

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 6.2.1.1

Introduced

ip msdp peer

Configure an MSDP peer.

S6000

Syntax

ip msdp peer

peer address

[connect-source] [description] [sa-

limit

number

]

To remove the MSDP peer, use the

no ip msdp peer

peer address

[connect-source interface] [description

name

] [sa-limit

number

]

command.

Parameters

peer address

Enter the peer address in a dotted decimal format (A.B.C.D.).

connect-
source

interface

Enter the keywords

connect-source

then one of the

interfaces and slot/port or number information:

• For a Fast Ethernet interface, enter the keyword

FastEthernet

then the slot/ port information.

• For a Loopback interface, enter the keyword

loopback

then a number from 0 to 16383.

• For a Port Channel interface, enter the keywords

port-

channel

then a number. The range is from 1 to 128.

• For a 1-Gigabit Ethernet interface, enter the keyword

GigabitEthernet

then the slot/port information.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

• For a VLAN, enter the keyword

vlan

then a number from

1 to 4094.

description
name

(OPTIONAL) Enter the keyword

description

then a

description name (maximum 80 characters) to designate a
description for the MSDP peer.

sa-limit

number

(OPTIONAL) Enter the maximum number of SA entries in SA-
cache. The range is from 1 to 500000. The default it

500000

Defaults

As described in the

Parameters

section.

Multicast Source Discovery Protocol (MSDP)

931

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands