Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 924 / 1510

background image

31

Multicast Source Discovery Protocol

(MSDP)

Multicast source discovery protocol (MSDP) connects multiple PIM Sparse-Mode (PIM-SM) domains

together.
MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is
reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP
connections.

The Dell Networking operating system supports MSDP commands on the S6000 platform.

clear ip msdp peer

Reset the TCP connection to the peer and clear all the peer statistics.

S6000

Syntax

clear ip msdp peer {

peer address

}

Parameters

peer address

Enter the peer address in a dotted decimal format (A.B.C.D.)

Defaults

Not configured.

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.1

Introduced on the S4810.

Version 6.2.1.1

Introduced

924

Multicast Source Discovery Protocol (MSDP)

«
...
922
923
924
925
926
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Brand: JB Systems Light Pages: 15

Brand: Brightlink Pages: 33

Brand: Delta Pages: 4

Brand: Field Controls Pages: 4

Brand: Movie Vision Pages: 2

Brand: SMC Networks Pages: 2

Brand: Omega Engineering Pages: 8

Brand: Attwood Pages: 2

Brand: Audio Authority Pages: 12

EX ZS 92 S 22 VD F

Brand: steute Pages: 28

StorageWorks SAN Switch Integrated/32

Brand: Compaq Pages: 104

Crocodile Tail Loop

Brand: One Control Pages: 9

MultiView CE-H26311-S1

Brand: SIIG Pages: 24

Hi-Speed USB 2.0 Hub

Brand: Saitek Pages: 14

ADDERView Secure AVS-4128

Brand: ADDER Pages: 24

SwitchMan USB-Combo SW4

Brand: Raritan Pages: 2

Giga-AcessEtherLinx-II

Brand: IMC Networks Pages: 40

Brand: Banner Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands