Dell Networking S6000 System Reference Manual Download

Page: 886 / 1510

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

pre-Version
6.2.1.1

Introduced on the E-Series.

Usage
Information

When this command is configured, the VLAN is operationally UP if any of the
interfaces specified in the

track ip

command are operationally UP, and the VLAN

is operationally DOWN if none of the tracking interfaces are operationally UP.

If the

track ip

command is not configured, the VLAN's Layer 3 operational state

depends on all the members of the VLAN.

The Layer 2 state of the VLAN, and hence the Layer 2 traffic, is not affected by the

track ip

command configuration.

Related
Commands

interface vlan

— configures a VLAN.

tagged

— specifies which interfaces in a VLAN are tagged.

untagged

Add a Layer 2 interface to a VLAN as an untagged interface.

S6000

Syntax

untagged

interface

To remove an untagged interface from a VLAN, use the

no untagged

interface

command.

Parameters

interface

Enter the following keywords and slot/port or number
information:

• For a Port Channel interface, enter the keywords

port-

channel

then a number. The range is from 1 to 128.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

886

Layer 2

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands