manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 744 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 744

pre-Version 
6.1.1.0

Introduced on the E-Series.

Usage 
Information

When a static route (or a protocol route) overlaps with Management static route, 
the static route (or a protocol route) is preferred over the Management Static route. 
Also, Management static routes and the Management Connected prefix are not 
reflected in the hardware routing tables. Separate routing tables are maintained for 
IPv4 and IPv6 management routes. This command manages both tables.

Related 
Commands

interface ManagementEthernet

 — configures the Management port on the system 

(either the Primary or Standby RPM).

speed (Management interface)

 — sets the speed for the Management interface.

show arp

Display the ARP table.

S6000

Syntax

show arp [vrf 

vrf-name

] [interface 

interface

 | ip 

ip-address 

[

mask

] | macaddress 

mac-address

 [

mac-address mask

]] [retries] 

[static | dynamic] [inspection {database | statistics][summary]

Parameters

vrf 

vrf-name

(OPTIONAL) Enter the keyword 

vrf

 and then the name of 

the VRF.

NOTE: Use this attribute to start a BGP instance for either 
a specific address family corresponding to the default 
VRF or an IPv4 address family corresponding to a non-
default VRF.

interface 

interface

(OPTIONAL) Enter the following keywords and slot/port or 
number information:

• For a 1-Gigabit Ethernet interface, enter the keyword 

GigabitEthernet

 then the slot/port information.

• For the Management interface, enter the keyword 

managementethernet

 then the slot/port information.

• For a Port Channel interface, enter the keyword 

port-

channel

 then a number. The range is from 1 to 128.

• For a 10-Gigabit Ethernet interface, enter the keyword 

TenGigabitEthernet

 then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword 

fortyGigE

 then the slot/port information.

• For a VLAN, enter the keyword 

vlan

 then a number from 

1 to 4094.

744

IPv4 Routing

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments