Dell Networking S6000 System Reference Manual Download

Page: 676 / 1510

Gi 0/11 Down Auto Auto --

Gi 0/12 Down Auto Auto --

Gi 0/13 Down Auto Auto --

Gi 0/14 Down Auto Auto --

Gi 0/15 Down Auto Auto -

Dell#

Related
Commands

show interfaces

— displays information on a specific physical interface or virtual

interface.

show interfaces switchport

Display only virtual and physical interfaces in Layer 2 mode. This command displays the Layer 2 mode

interfaces’ IEEE 802.1Q tag status and VLAN membership.

S6000

Syntax

show interfaces switchport [

interface

| stack-unit

unit-id

]

Parameters

interface

(OPTIONAL) Enter one of the following keywords and slot/
port or number information:

• For a Port Channel interface, enter the keywords

port-

channel

then a number. The range is from 1 to 128.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

• Enter the keyword

backup

to view the backup interface

for this interface.

stack-unit

unit-

(OPTIONAL) Enter the keywords

stack-unit

then the stack

member number. This option is available only on S-Series.
The range is from 0 to 5.

Command
Modes

• EXEC
• EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

676

Interfaces

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands