Dell Networking S6000 System Reference Manual Download

Page: 664 / 1510

Example

Dell(conf)#interface range gigabitethernet 1/1 - 2

Dell(conf-if-range-gi-1/1-2)#show config

interface GigabitEthernet 1/1

no ip address

switchport

no shutdown

interface GigabitEthernet 1/2

no ip address

switchport

no shutdown

Dell(conf-if-range-gi-1/1-2)#

show interfaces

Display information on a specific physical interface or virtual interface.

S6000

Syntax

show interfaces

interface

Parameters

interface

Enter one of the following keywords and slot/port or number
information:

• For a Loopback interface, enter the keyword

loopback

followed by a number from 0 to 16383.

• For stack-units, enter the keywords

stack-unit

then

the slot/port information. The range is from 0 to 11.

• For a Null interface, enter the keywords

null 0

• For a Port Channel interface, enter the keywords

port-

channel

then a number. The range is 1 to 128.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

• For a VLAN interface, enter the keyword

vlan

then a

number from 1 to 4094.

• For a tunnel interface, enter the keyword

tunnel

then

the tunnel ID. The range is from 1 to 16383.

Command
Modes

• EXEC
• EXEC Privilege

Command
History

Version 9.0.2.0

Introduced on the S6000.

Version 9.2(0.2)

Added support for the tunnel interface type.

Version 9.1(0.0)

Updated ManagementEthernet output to include two global
IPv6 addresses on S4810 and Z9000 and added output
example showing OpenFlow instance ID.

664

Interfaces

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands