Dell Networking S6000 System Reference Manual Download

Page: 593 / 1510

Related
Commands

show gvrp statistics

— displays the GVRP statistics.

debug gvrp

Enable debugging on GVRP.

S6000

Syntax

debug gvrp {config | events | pdu}

To disable debugging, use the

no debug gvrp {config | events | pdu}

command.

Parameters

config

Enter the keyword

config

to enable debugging on the

GVRP configuration.

event

Enter the keyword

event

to enable debugging on the JOIN/

LEAVE events.

pdu

Enter the keyword

pdu

then one of the following Interface

keywords and slot/port or number information:

• For a Port Channel interface, enter the keywords

port-

channel

then a number. The range is from 1 to 128.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

Defaults

Disabled.

Command
Modes

EXEC

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on C-Series, E-Series, and S-Series

GARP VLAN Registration (GVRP)

593

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands