Dell Networking S6000 System Reference Manual Download

Page: 452 / 1510

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version
8.3.12.0

Introduced on the S4810.

Version
8.3.16.0

Introduced on the MXL 10/40GbE Switch IO Module.

Usage
Information

If you do not use the

statistics

parameter, both hardware and DCBx counters

clear.

dcb-input

To apply pause or flow control for specified priorities using a configure delay time, create a DCB input

policy.

S6000

Syntax

dcb-input

policy-name

To delete the DCB input policy, use the

no dcb-input

command.

Parameters

policy-name

Maximum: 32 alphanumeric characters.

Defaults

none

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version
8.3.12.0

Introduced on the S4810.

Version
8.3.16.0

Introduced on the MXL 10/40GbE Switch IO Module.

452

Data Center Bridging (DCB)

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands