Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 371 / 1510

background image

no prepend

Specifies that local AS values do not prepend to
announcements from the neighbor.

Defaults

Not configured.

Command
Modes

ROUTER BGP

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

Usage
Information

If a local-as is configured, BGP does not allow for the configuration of BGP
confederation. Similarly, if BGP confederation is configured, then BGP does not
allow the configuration of local-as.

This command automatically restarts the neighbor session for the configuration to
take effect.

Related
Commands

bgp four-octet-as-support

— enables 4-byte support for the BGP process.

neighbor maximum-prefix

Control the number of network prefixes received.

S6000

Syntax

neighbor {

ip-address

|

peer-group-name

} maximum-prefix

maximum

[

threshold

] [warning-only]

To return to the default values, use the

no neighbor {

ip-address

|

peer-

group-name

} maximum-prefix

maximum

command.

Parameters

ip-address

Enter the IP address of the neighbor in dotted decimal
format.

peer-group-
name

Enter the name of the peer group.

Border Gateway Protocol

371

«
...
369
370
371
372
373
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

EasySmart DGS-1100-08

Brand: D-Link Pages: 44

Brand: pathway Pages: 28

Brand: GE Pages: 302

Brand: D-Box Pages: 27

Brand: 3Com Pages: 12

S7906E - Switch

Brand: 3Com Pages: 8

Brand: Eaton Pages: 4

Brand: Adler Pages: 8

PowerSwitch Z9332F-ON

Brand: Dell EMC Pages: 16

Draco major K474-U8/C8

Brand: Ihse Pages: 167

Brand: steute Pages: 10

DSR Series DSR1030

Brand: Avocent Pages: 8

Brand: Wavetronix Pages: 3

Brand: Ubiquiti Pages: 14

Brand: Milestone pro Pages: 32

Brand: Kramer Pages: 11

Brand: Black Box Pages: 2

Thunder series 930

Brand: A10 Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands