Dell Networking S6000 System Reference Manual Download

Page: 1484 / 1510

Usage
Information

You must disable

vxlan-instance

before unconfiguring VAP.

Related
Commands

feature vxlan

—Enable VXLAN configuration globally on the platform.

max_backoff

Configures time to wait between connection attempts with controller.

S6000

Syntax

max_backoff

time

Parameters

time

Enter the time in milliseconds. The range is from
1000-180000. The default value is 30000.

Defaults

30000

Command
Modes

VXLAN INSTANCE

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

Version 9.4.
(0.0)

Introduced on the S6000.

Usage
Information

The retry interval value caps at the value configured on the max-backoff.

Related
Commands

vxlan-instance

— Enable VXLAN Instance configuration on the platform.

gateway-ip

Configures gateway IP address on the platform.

S6000

Syntax

gateway-ip

IP address

Parameters

IP address

Enter the IP address of the gateway for the VXLAN instance.

1484

Virtual Extensible LAN (VXLAN)

«
...
1482
1483
1484
1485
1486
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands