Dell Networking S6000 System Reference Manual Download

Page: 1481 / 1510

Virtual Extensible LAN (VXLAN)

Virtual Extensible LAN (VXLAN) is supported on the S6000 platform.

feature vxlan

Enable VXLAN configuration globally on the platform.

S6000

Syntax

feature vxlan

To disable the VXLAN, use the

no feature vxlan

command.

Defaults

Disabled

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

Version 9.4.
(0.0)

Introduced on the S6000.

Usage
Information

You must configure feature VXLAN to configure VXLAN-instance.

Related
Commands

vxlan-instance

— Enable VXLAN Instance configuration on the platform.

debug vxlan

Debug messages between the Gateway and Controller.

S6000

Syntax

debug vxlan

Defaults

Disabled

Virtual Extensible LAN (VXLAN)

1481

«
...
1479
1480
1481
1482
1483
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands