Dell Networking S6000 System Reference Manual Download

Page: 1444 / 1510

Number

Resulting TPID

0x0081

8100

0x8100

Related
Commands

portmode hybrid

— sets a port (physical ports only) to accept both tagged and

untagged frames. A port configured this way is identified as a hybrid port in report
displays.

vlan-stack trunk

— specifies a Layer 2 port or port channel as a trunk port to the

Stackable VLAN network.

vlan-stack trunk

Specify a Layer 2 port or port channel as a trunk port to the Stackable VLAN network.

S6000

Syntax

vlan-stack trunk

To remove a trunk port designation from the selected interface, use the

no vlan-

stack trunk

command.

Defaults

Not configured.

Command
Modes

INTERFACE

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.2.1.0

Introduced on the E-Series ExaScale. C-Series and S-Series
accept both bytes of the 2-byte S-Tag TPID.

Version 7.8.1.0

Functionality augmented for C-Series and S-Series to enable
multi-purpose use of the port.

Version 7.7.1.0

Functionality augmented for E-Series to enable multi-
purpose use of the port.

1444

VLAN Stacking

«
...
1442
1443
1444
1445
1446
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands