Dell Networking S6000 System Reference Manual Download

Page: 1278 / 1510

show dot1x interface

Display the 802.1X information on an interface.

S6000

Syntax

show dot1x interface

interface

Parameters

interface

Enter one of the following keywords and slot/port or number
information:

• For a Gigabit Ethernet interface, enter the keyword

GigabitEthernet

then the slot/port information.

• For a Fast Ethernet interface, enter the keyword

FastEthernet

then the slot/ port information.

• For a ten-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

Defaults

none

Command
Modes

• EXEC
• EXEC privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.5.1.0

Added support for 4-port 40G line cards on ExaScale.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on the C-Series, S-Series, and E-Series.

Example

Dell#show dot1x int Gi 2/32

802.1x information on Gi 2/32:

-----------------------------

Dot1x Status: Enable

Port Control: AUTO

Port Auth Status: UNAUTHORIZED

Re-Authentication: Disable

Untagged VLAN id: None

Guest VLAN: Enable

Guest VLAN id: 10

Auth-Fail VLAN: Enable

1278

Security

«
...
1276
1277
1278
1279
1280
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands