manualshive.com logo in svg

Dell Networking S6000 System, Reference Manual, Page: 1157 / 1510

Share
Download
Dell Networking S6000 System Reference Manual Download Page 1157

qos dscp-color-map

Configure the DSCP color map.

Syntax

qos dscp-color-map 

map-name

To remove a color map, use the no 

qos dscp-color-map

 

map-name

 command.

Parameters

map-name

Enter the name of the DSCP color map. The map name can 
have a maximum of 32 characters.

Defaults

None

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.5.0.0

Introduced on the Z9000, S6000, S4820T, S4810, and MXL.

Usage 
Information

A color map outlines the codepoint mappings to the appropriate color mapping 
(green, yellow, red) for the traffic. The system uses this information use to handle 
the traffic on the interface based on the traffic priority and places it into the 
appropriate shaping queue. You cannot delete a DSCP color map when it is 
configured on an interface. If you do, all the DSCP values are set to green (low 
drop precedence). To delete the DSCP color map that is being used by one or 
more interfaces, remove the DSCP map from each interface.

Example

Dell(conf)#qos dscp-color-map mymap

Related 
Commands

qos dscp-color-map

— associates the DSCP color map profile with an interface so 

that all IP packets received on it is given a color based on that color map

dscp

— sets the number of specific DSCP values for color map profile to yellow or 

red.

qos dscp-color-policy

Associates the DSCP color map profile with an interface so that all IP packets received on it is given a 
color based on that color map.

Syntax

dscp-color-policy 

color-map-profile-name

To remove a color policy map profile, use the no

 dscp-color-policy 

color-

map-profile-name 

command.

Quality of Service (QoS)

1157

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments