Dell Networking S6000 System Reference Manual Download

Page: 110 / 1510

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

E-Series

Original command.

Usage
Information

If there is a change in the configuration, FTOS prompts you to save the new
configuration. Or you can save your running configuration with the

copy

running-config

command. Use the conditional parameter if any configuration

changes made to the nvram, such as stack-group and fanout configurations, must
be saved.

send

Send messages to one or all terminal line users.

S6000

Syntax

send [*] | [line ] | [console] | [vty]

Parameters

Enter the asterisk character

to send a message to all tty

lines.

line

Send a message to a specific line. The range is from 0 to 11.

console

Enter the keyword

console

to send a message to the

primary terminal line.

vty

Enter the keyword

vty

to send a message to the virtual

terminal.

Defaults

none

Command
Modes

EXEC

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.0.0.0

Introduced on the Z9000.

Version
8.3.19.0

Introduced on the S4820T.

Version
8.3.12.0

Introduced on the S4810.

Version 8.3.11.1

Introduced on the Z9000.

110

Control and Monitoring

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands

Dell Networking S6000 System, Reference Manual

Search results

Summary of Contents for Networking S6000 System

Reviews:

Related manuals for Networking S6000 System

Brands by name

Popular brands