Dell Networking S6000 System Reference Manual Download | Manualshive

Page: 100 / 1510

background image

ip ftp vrf

Configures an FTP client with a VRF that is used to connect to the FTP server.

Syntax

ip ftp [vrf

vrf-name

]

To undo the FTP client configuration, use the

ip ftp [vrf

vrf-name

]

command.

Parameters

vrf

vrf-name

Enter the keyword

vrf

and then the name of the VRF to

specify the VRF that is used by the FTP client.

Defaults

Disabled

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

FTOS Command Line Reference Guide

.

The following is a list of the FTOS version history for this command.

Version 9.4.
(0.0)

Introduced on the S-Series and Z-Series.

Usage
Information

Use this command to make the FTP clients VRF aware. The VRF name that you
specify is used by the FTP client to reach the FTP server. If no VRF is specified, then
the default vrf is used.

ip telnet server enable

Enable the Telnet server on the switch.

S6000

Syntax

ip telnet server enable

To disable the Telnet server, use the

no ip telnet server enable

command.

Defaults

Enabled

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

100

Control and Monitoring

«
...
98
99
100
101
102
...
»

Summary of Contents for Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Networking S6000 System

Switch 4500 Family

Brand: 3Com Pages: 16

PathBuilder S200 Series

Brand: 3Com Pages: 32

Brand: Eaton Pages: 8

3CR17251-91 - Switch 5500G-EI Stackable Gigabit...

Brand: 3Com Pages: 148

Brand: Cabletron Systems Pages: 110

Brand: Edge-Core Pages: 9

Brand: Velleman Pages: 5

Brand: Eaton Pages: 120

Brand: Unipoe Pages: 41

Brand: VADA Pages: 4

SmartStack STS16-20R

Brand: Cabletron Systems Pages: 258

Brand: Wyrestorm Pages: 4

Brand: Quidway Pages: 43

Brand: DeLOCK Pages: 26

Brand: Lindy Pages: 6

Brand: Zektor Pages: 30

Brand: TRENDnet Pages: 32

Brand: JUKI Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands