Dell Latitude 5430 Service Manual Download Page 66

Page: 66 / 139

Steps

1. Replace the two (M2.5x5) screws to secure the rear I/O board to the system board and connect the rear I/O flat printed

cable.
Adhere the rear I/O flat printed cable with kapton tapes to the connector.

2. Route the cables using the routing channels on the system chassis and adhere the adhesive tape on the rear I/O board.

Next steps

1. Install the

base cover

2. Install the

primary M.2 2280 solid state drive

primary M.2 2230 solid state drive

3. Install the

battery

4. Follow the procedure in

after working inside your computer

System board

Removing the system board

Prerequisites

1. Follow the procedure in

before working inside your computer

2. Remove the

battery

3. Remove the

primary M.2 2280 solid state drive

primary M.2 2230 solid state drive

4. Remove the

5. Remove the

6. Remove the

7. Remove the

8. Remove the

9. Remove the

10. Remove the

11. Remove the

12. Remove the

About this task

The following image indicates the connectors on your system board.

Removing and installing components

Summary of Contents for Latitude 5430












































































































































Search results

Summary of Contents for Latitude 5430

Reviews:

Related manuals for Latitude 5430

Brands by name

Popular brands

Dell Latitude 5430, Service Manual

Search results

Summary of Contents for Latitude 5430

Reviews:

Related manuals for Latitude 5430

Brands by name

Popular brands