Dell Latitude 5430 Service Manual Download Page 24 | Manualshive

Page: 24 / 139

background image

Steps

1. Remove the (M2x4) screw on the SSD door latch cover.
2. Push the SSD latch and lift the SSD door.
3. Push the carrier latch to release the SSD carrier.
4. Pull the mylar tape to lift the SSD carrier of the computer.
5. Flip the SSD carrier and remove the (M2x5) screw.
6. Pull the mylar tape and lift the SSD carrier cover.
7. Remove the M.2 2280 solid state drive.

Installing the primary M.2 2280 solid state drive

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the primary solid state drive and provides a visual representation of the installation
procedure.

24

Removing and installing components

«
...
22
23
24
25
26
...
»

Summary of Contents for Latitude 5430












































































































































Reviews:

No comments

Related manuals for Latitude 5430

ThinkPad i Series

Brand: IBM Pages: 5

Thinkpad X30 Series

Brand: IBM Pages: 22

Brand: IBM Pages: 2

Brand: Gateway Pages: 8

Brand: Gateway Pages: 1

Brand: Gateway Pages: 106

Brand: Hama Pages: 22

MX6440 - Notebook Computer

Brand: Gateway Pages: 1

Brand: Epson Pages: 11

Brand: Lenovo Pages: 84

3i-15 Chromebook

Brand: Lenovo Pages: 42

Brand: Lenovo Pages: 4

Brand: Lenovo Pages: 4

Brand: Lenovo Pages: 108

Brand: Lenovo Pages: 4

Brand: Lenovo Pages: 6

Brand: Lenovo Pages: 4

Brand: Lenovo Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands