Dell Latitude 5430 Service Manual Download | Manualshive

Page: 60 / 139

background image

5. Lift the secondary daughterboard from the system chassis.

Installing the secondary daughterboard

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the secondary daughterboard and provides a visual representation of the
installation procedure.

Steps

1. Align the screw holes and replace the two (M2x3.5) screws that secure the secondary daughterboard with system chassis.
2. Connect the contactless smartcard flat printed cable and fingerprint cable to the connector on the secondary

daughterboard.
Adhere the contactless smartcard flat printed cable and fingerprint cable with kapton tapes to the connector.

3. Connect the touchpad flat printed cable to the connector on the touchpad.
4. Connect the secondary daughterboard flat printed cable and smart card cable to the connector on the secondary

daughterboard.
Adhere the secondary daughterboard flat printed cable and smart card cable with kapton tapes to the connector.

60

Removing and installing components

«
...
58
59
60
61
62
...
»

Summary of Contents for Latitude 5430












































































































































Reviews:

No comments

Related manuals for Latitude 5430

TravelMate 4100 Series

Brand: Acer Pages: 86

TravelMate 4060

Brand: Acer Pages: 69

Brand: Hama Pages: 22

Brand: Alienware Pages: 124

Galaxy Book Flex

Brand: Samsung Pages: 119

TravelMate 4750

Brand: Acer Pages: 315

TravelMate 520 Series

Brand: Acer Pages: 83

Brand: Acer Pages: 354

Brand: Acer Pages: 274

Brand: Acer Pages: 230

CHROMEBOOK C204EE

Brand: Asus Pages: 94

Brand: Asus Pages: 71

Brand: NEC Pages: 89

Packard Bell EasyNote M5

Brand: NEC Pages: 28

Brand: NEC Pages: 47

VERSA 2000 WINDOWS 98 - UPGRADE INFORMATION

Brand: NEC Pages: 4

ShieldPRO FC-N21S

Brand: NEC Pages: 16

Brand: NEC Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands