Dell INSPIRON Inspiron 5000 Service Manual Download Page 85

Page: 85 / 100

Removing the CPU board

NOTE:

Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box

PC and follow the steps in

Before working inside your Embedded Box PC

. After working inside your Embedded Box PC,

follow the steps in

After working inside your Embedded Box PC

. For more safety best practices, see the Regulatory

Compliance home page at

www.dell.com/regulatory_compliance

Topics:

•

Prerequisites

•

Procedure

Prerequisites

1. Follow step 1 to step 6 in “

Removing the back cover

”.

2. Remove the

3. Remove the

4. Remove the

Procedure

NOTE:

When removing the CPU board, take note of the existing DIP switch settings and ensure that the same DIP

switch settings are applied to the new CPU board. For more information, see

DIP switch settings

1. Remove the screws that secure the CPU board to the system board.
2. Lift the CPU board off the system board.

a. M2.5x6 screws (2)
b. STDF(L5) HEX, M2.5x4 screws (3)
c. CPU board

Removing the CPU board

Summary of Contents for INSPIRON Inspiron 5000





































































































Search results

Summary of Contents for INSPIRON Inspiron 5000

Reviews:

Related manuals for INSPIRON Inspiron 5000

Brands by name

Popular brands

Dell INSPIRON Inspiron 5000, Service Manual

Search results

Summary of Contents for INSPIRON Inspiron 5000

Reviews:

Related manuals for INSPIRON Inspiron 5000

Brands by name

Popular brands