Dell INSPIRON Inspiron 5000 Service Manual Download Page 60

Page: 60 / 100

Removing the coin-cell battery

NOTE:

Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box

PC and follow the steps in

Before working inside your Embedded Box PC

. After working inside your Embedded Box PC,

follow the steps in

After working inside your Embedded Box PC

. For more safety best practices, see the Regulatory

Compliance home page at

www.dell.com/regulatory_compliance

CAUTION:

Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is recommended that

you note the BIOS setup program’s settings before removing the coin-cell battery.

Topics:

•

Prerequisites

•

Procedure

Prerequisites

1. Follow step 1 to step 6 in “

Removing the back cover

”.

2. Remove the

PCI/PCIe card

(if installed).

Procedure

1. Using a plasic scribe, push the battery-release lever away from the coin-cell battery until the coin-cell battery pops up.
2. Lift the coin-cell battery out of its socket.

a. plastic scribe
b. battery-release lever

Removing the coin-cell battery

Summary of Contents for INSPIRON Inspiron 5000





































































































Search results

Summary of Contents for INSPIRON Inspiron 5000

Reviews:

Related manuals for INSPIRON Inspiron 5000

Brands by name

Popular brands

Dell INSPIRON Inspiron 5000, Service Manual

Search results

Summary of Contents for INSPIRON Inspiron 5000

Reviews:

Related manuals for INSPIRON Inspiron 5000

Brands by name

Popular brands